How to replace a basement window with your own hands

How to replace basement windowsBefore answering the question how to replace a basement windows it should be notices that there are some general requirments to the process itself. Find out that each of them works before start your working. These aspects are for windows in concrete foundation, concrete block foundation, cinder blocks foundation with block and brick walls above.

  • Old window frame, wall and weather-resistant barrier must be adequate and window frame and wall must be structurally sound.
  • Window must be installed to be plumb, level and square.
  • The replacement window should be approximately 1/4 less in width and height than the existing window opening once the old sash and components have been removed.
  • Read all the guides you have before starting installation.
  • Contact local authorities or waste management companies for proper recycling and/or disposal of removed window or patio door.
  • Due to ongoing product changes, updated test results and/or new industry best practices, this installation procedure may change over time.

You will need:

  • work gloves
  • safety glasses
  • tape measure
  • 6' level
  • framer’s square
  • chisel
  • putty knife
  • backer rod
  • minimum expanding foam sealant
  • interior and exterior window grade sealant
  • caulk gun (How to caulk a window)
  • power driver and bits
  • utility knife or other cutting tool
  • shims hammer
  • finish nails
  • appropriate fasteners

Basement window insertFinishing, cleaning and maintenance rules:

  • Do not stain or paint windows with metal frame. Product damage may occur.
  • Clean glass using liquid glass cleaner.
  • Clean exterior frame, sash, and insect screens using mild detergent and water with a soft cloth or brush.
  • For hard to clean areas use a non-abrasive cleaner, alcohol-and-water or ammonia-and-water.
  • Do not apply any type of film to insulating glass. Thermal stress and glass damage can result. Shading devices (insulated coverings, shutters, etc.) may also cause thermal stress damage.

Step 1 - Inspecting new window and verify opening

Inspect for proper size and condition and verify that all parts are included. Inspect existing wall and rough opening for structural decay. Repair as needed.

Step 2 - Clearing the opening of any debris

Remove all material that may interfere with installation process. Check sill plate for level. Sill must be level. Shim sill plate if necessary. Check opening for plumb and level. If opening is not plumb or level, correct as necessary. Check opening for square by measuring diagonally, upper left to lower right and upper right to lower left corner. Measurements must be within 1/8". If opening is not square, correct as necessary. Inspect opening for correct size. Opening should be 1/2" larger than window size in width and height.

Attention! Sliding window shown for illustration purposes. These instructions also cover hopper windows.

Recommend: How to measure windows for replacement.

Step 3 - Adding wood frame if necessary

Tools required to install basement windowIf it's necessary, construct a frame using preservative treated wood of the appropriate depth for your opening (typically 2 x 6 or 2 x 8). Secure the frame to the opening using appropriate fasteners (masonry screws, anchors, etc.). Recheck for plumb, level and square.

Step 4 - Checking fit of window

Temporarily place the window in the frame tilting in from the bottom and check for fit. Then remove window. Adjust opening as needed.

Step 5 - Adding a "blind stop"

Create a "blind stop" for the window, using a 3/4" quarterround or comparable piece of wood around the top and sides of the wood frame. Make sure the inside of the "blind stop" is at least 4" from the inside of the wood frame, leaving enough room to install the window and interior trim. Recheck for plumb, level and square. Use finish nails to secure the "blind stop".

Step 6 - Drilling installation holes

If installing a window that does not have pre-drilled installation holes, open sash. Drill the installation holes according to the fastening instructions from local building code. Countersink holes so top of fastener does not interfere with window operation.

Step 7 - Applying sealant to opening

Apply sealant to inside edge of blind stops where window will contact them. Also apply sealant to bottom of wood frame where window will contact frame. NOTE: If blind stop is not used, apply backer rod and sealant between window and frame.

Step 8 - Placing the window into opening and shim

How to replace a basement windowPlace window into opening, tilting in from bottom, and seat securely against blind stops. Make sure weep holes are on the bottom and facing outside, if applicable. Lock and/or handle should be on the interior. Shim behind each installation hole in the frame. Check for plumb, level and square as needed.

Step 9 - Fastening your new window

Open each sash and drill 1/8" pilot holes through pre-drilled holes. Fasten window to frame using supplied installation screws if applicable, or appropriate fasteners. Do not over tighten screws.

We hope this article helped you in case you were searching an answer to the question how to replace basement windows

You might be interested in:

How to make a window frame and properly install it
How to replace a window pane with your own hands
The ways of sealing windows and the main types of sealants
The ways of glazing windows with your own hands
The ways to prevent appearing of condensation on double glazed windows in your house
How to caulk windows using various materials